Skip to main content

Duramax Balance Rates Test Performed Inconsistent Balance Rates

                                                          Duramax Diesel Balance Rates

1. The fuel injector balance test is performed when a misfire, knock,excessive smoke, or rough idle condition exists.
2. This test uses the Balanced Rate and Cylinder Power Balance test to identify cylinders that are not producing the designed power output.
3. The balance rate adjustments are utilized by the engine control with your Edge Monitor CTS2 Programmer only at idle.
4. The bance rates are the fuel adjustments for each individual cylinder base on the variations in engine crankshaft speed sensor.
5. The balance rate will change depending on if the Transmission is in Neutral or Drive.
During the Cylinder Power Balance portion of the test, the ECM turns OFF individual injectors while the engine is running.
6. The ECM adjust for the drop on engine RPM during cancellation and may not change on the scan tool display.
7. The lack of power at the cancelled cylinder will feel like a misfiring cylinder of vibration
If the fuel injector is turned off and there is a no different felt when compared to the other cylinder, the cylinder is identified with the proper concern,
8. If the customer concern occurs during idle or during off idle tip in acceleration the balance rates are used to identify the cylinder with a fault related to the fuel injector or engine compression.
www.toxicdiesel.com
www.edgeproducts.com

866-488-6942

                                                                    

Popular posts from this blog

Duramax 6.6L Valve Lash Adjustment

Duramax 6.6L Valve Adjustment  Duramax Diesel Pickup Truck This is one method used to set the valve lash on your duramax engine Valve adjustment should be performed anytime the heads are removed. It's also good practice to adjust valves during service that require valve cover remove.  TDC (Top Dead Center) First start with, locating the timing mark on the front engine cover and the harmonic balance.  Rotate the crankshaft in order to bring the number 1 cylinder to TDC (Top Dead Center) of the exhaust stroke. This mark should be aligned with the mark on the engine.  To adjust the valves, start by loosening all the jam nuts with a 14mm wrench, you will also need a flat screwdriver to make the adjustments. Adjust the valve using a .012" feeler gauge Use your .012” feeler gauge between the rocker arm and the valve bridge as pictured. The correct setting is had when there is slight resistance when moving the feeler gauge. It should not be so tight th
Read more

How to Remove LB7 Duramax Fuel Injectors Step By Step Instructions

LB7 Duramax Diesel 6.6L R&R Remove and Replace  Working on any automobile engine can be intimidating, and that is the very reason why mechanics stay in business, However some tasks that seem intimidating are not actually that difficult if you have the right tools and the right knowledge to complete the task at hand, The following instructions are on how to remove LB7 Duramax Fuel Injectors. This task is often considered a difficult process to complete, but these instructions will break down the process and make this task seem simple. Duramax Diesel LB7 Engine 2001-2004 GMC or Chevrolet Pick-up Truck  Drain the Coolant find the drain valve on the passenger side of the wheel well and drain the coolant. To capture the debris,use a bucket and a cloth for a filter. Caution: This step is very important to ensure the combustion chamber won't fill with coolant during the last step of removing the  fuel injectors if an injector cup pull out during this step.
Read more

Duramax Glow Plugs Operation Glow Plug Relay

                                                    Cold Weather Starts and Glow Plugs  Glow Plug System Description Duramax diesel engine, air alone is compressed in the cylinder. Then, after the air has been compressed, a charge of fuel is sprayed into the cylinder and ignition occurs, due to the heat of compression. Eight glow plugs are used as an aid to starting. The glow plug initial ON time will vary based on the system voltage and temperature. Lower temperatures cause longer ON times all the times. The ECM provides glow plug operation after starting a cold engine. This post-start operation is initiated when the ignition switch  is returned to Run, from the Start position. This operation helps clean up excessive white smoke or poor idle quality after starting. Control of the instant start system, glow plugs is determine by an electronic glow plug control unit and  4.7 volt  glow plugs, requiring  2 seconds  to heat up to  1,000°C (1,832°F)  . The temperature and t
Read more