AFE Power Duramax Intercooler Tubes

AFE Power Duramax Intercooler Tubes - Pipes

AFE Power Duramax 6.6L Diesel 3" Intercooler Tube

Get the most out of your diesel Truck with AFE Power BladeRunner intercooler pipes. These connecting arms are fully mandrel-bent stainless steel or aluminum tubing that will out flow pipes, giving you more power and fuel efficiency. Their Free flowing design aids in decresing EGT (Exhaust Gas Temperature) to help protect your motor from power robbing heat. The AFE Power BladeRunner pipes are available for these positions: Turbocharger-to-intercooler, intercooler-to-intake, and the complete system. The kits come complete with all the hardware needed for and easy installation. The pipes are powdercoat black or red finish to protect them from the elements.

Don't let your factory plumbing rob you of power-upgrade with AFE Power BladeRunner Duramax Intercooler pipes.

2011-2013 GM Duramax Silverado Diesel 6.6 BladeRunner 3" Intercooler Tube Out; GM Diesel Trucks 11-13 V8-6.6L (td) LML

Part Number: AFE46-20119

Price at: 245.00 Free 2nd Day Air Shipping, Call 435-628-5544 or

Visit our Website toxicdiesel.com

Toxic Diesel Performance

AFE Power Products

Duramax 6.6L Valve Lash Adjustment

Duramax 6.6L Valve Adjustment Duramax Diesel Pickup Truck This is one method used to set the valve lash on your duramax engine Valve adjustment should be performed anytime the heads are removed. It's also good practice to adjust valves during service that require valve cover remove. TDC (Top Dead Center) First start with, locating the timing mark on the front engine cover and the harmonic balance. Rotate the crankshaft in order to bring the number 1 cylinder to TDC (Top Dead Center) of the exhaust stroke. This mark should be aligned with the mark on the engine. To adjust the valves, start by loosening all the jam nuts with a 14mm wrench, you will also need a flat screwdriver to make the adjustments. Adjust the valve using a .012" feeler gauge Use your .012” feeler gauge between the rocker arm and the valve bridge as pictured. The correct setting is had when there is slight resistance when moving the feeler gauge. It should not be so tight th

How to Remove LB7 Duramax Fuel Injectors Step By Step Instructions

LB7 Duramax Diesel 6.6L R&R Remove and Replace Working on any automobile engine can be intimidating, and that is the very reason why mechanics stay in business, However some tasks that seem intimidating are not actually that difficult if you have the right tools and the right knowledge to complete the task at hand, The following instructions are on how to remove LB7 Duramax Fuel Injectors. This task is often considered a difficult process to complete, but these instructions will break down the process and make this task seem simple. Duramax Diesel LB7 Engine 2001-2004 GMC or Chevrolet Pick-up Truck Drain the Coolant find the drain valve on the passenger side of the wheel well and drain the coolant. To capture the debris,use a bucket and a cloth for a filter. Caution: This step is very important to ensure the combustion chamber won't fill with coolant during the last step of removing the fuel injectors if an injector cup pull out during this step.

Duramax Glow Plugs Operation Glow Plug Relay

Cold Weather Starts and Glow Plugs Glow Plug System Description Duramax diesel engine, air alone is compressed in the cylinder. Then, after the air has been compressed, a charge of fuel is sprayed into the cylinder and ignition occurs, due to the heat of compression. Eight glow plugs are used as an aid to starting. The glow plug initial ON time will vary based on the system voltage and temperature. Lower temperatures cause longer ON times all the times. The ECM provides glow plug operation after starting a cold engine. This post-start operation is initiated when the ignition switch is returned to Run, from the Start position. This operation helps clean up excessive white smoke or poor idle quality after starting. Control of the instant start system, glow plugs is determine by an electronic glow plug control unit and 4.7 volt glow plugs, requiring 2 seconds to heat up to 1,000°C (1,832°F) . The temperature and t

Toxic Performance

Search This Blog