Bushwacker Pocket Fender Flares

Bushwacker Pocket Fender Flares

For more than 40 years, Bushwacker has been surprising customers with stylish and innovative truck accessories. The company manufactures accessories for the Chevy, Dodge, Ford and GMC, Besides, Bushwacker offers Trail Armor pieces for the Jeep Wrangler. From the first fender flares developed for the Ford Bronco to the latest releases, Bushwacker's passion and determination to craft 'simply the best' products goes on and on.

Pocket Fender Flares

Bushwacker Fender Flares are made to be flexible enough to withstand any environment you put them in. From the debris on the roads to the brush on the trails and any other elements that wear on them every day, Bushwacker flares are designed to never relent to punishment and maintain their style. Made with complete UV protection, Bushwacker flares are also backed by a Limited Lifetime Warranty against warping, cracking or other factory defects.

Bushwacker

ICONIC BOLT-ON LOOK, EASY INSTALLATION

The rugged look of bolted-on flares without drilling through the body. Adds significant tire coverage to keep dirt and debris off the vehicle

HEAVY-DUTY HARDWARE

Whether on-road or off, our hardware holds the flares securely in place

100% UV-PROTECTED OE MATTE BLACK FINISH
Easily paintable to match your vehicle

LIMITED LIFETIME WARRANTY

Toxic Diesel Performance

Bushwacker Inc

866-488-6942

Duramax 6.6L Valve Lash Adjustment

Duramax 6.6L Valve Adjustment Duramax Diesel Pickup Truck This is one method used to set the valve lash on your duramax engine Valve adjustment should be performed anytime the heads are removed. It's also good practice to adjust valves during service that require valve cover remove. TDC (Top Dead Center) First start with, locating the timing mark on the front engine cover and the harmonic balance. Rotate the crankshaft in order to bring the number 1 cylinder to TDC (Top Dead Center) of the exhaust stroke. This mark should be aligned with the mark on the engine. To adjust the valves, start by loosening all the jam nuts with a 14mm wrench, you will also need a flat screwdriver to make the adjustments. Adjust the valve using a .012" feeler gauge Use your .012” feeler gauge between the rocker arm and the valve bridge as pictured. The correct setting is had when there is slight resistance when moving the feeler gauge. It should not be so tight th

How to Remove LB7 Duramax Fuel Injectors Step By Step Instructions

LB7 Duramax Diesel 6.6L R&R Remove and Replace Working on any automobile engine can be intimidating, and that is the very reason why mechanics stay in business, However some tasks that seem intimidating are not actually that difficult if you have the right tools and the right knowledge to complete the task at hand, The following instructions are on how to remove LB7 Duramax Fuel Injectors. This task is often considered a difficult process to complete, but these instructions will break down the process and make this task seem simple. Duramax Diesel LB7 Engine 2001-2004 GMC or Chevrolet Pick-up Truck Drain the Coolant find the drain valve on the passenger side of the wheel well and drain the coolant. To capture the debris,use a bucket and a cloth for a filter. Caution: This step is very important to ensure the combustion chamber won't fill with coolant during the last step of removing the fuel injectors if an injector cup pull out during this step.

Duramax Glow Plugs Operation Glow Plug Relay

Cold Weather Starts and Glow Plugs Glow Plug System Description Duramax diesel engine, air alone is compressed in the cylinder. Then, after the air has been compressed, a charge of fuel is sprayed into the cylinder and ignition occurs, due to the heat of compression. Eight glow plugs are used as an aid to starting. The glow plug initial ON time will vary based on the system voltage and temperature. Lower temperatures cause longer ON times all the times. The ECM provides glow plug operation after starting a cold engine. This post-start operation is initiated when the ignition switch is returned to Run, from the Start position. This operation helps clean up excessive white smoke or poor idle quality after starting. Control of the instant start system, glow plugs is determine by an electronic glow plug control unit and 4.7 volt glow plugs, requiring 2 seconds to heat up to 1,000°C (1,832°F) . The temperature and t

Toxic Performance

Search This Blog