Skip to main content

FASS Ride Fuel Filter System Duramax Diesel Delete Canister

DURAMAX FUEL FILTER DELETE


The New! Duramax diesel filter delete canister fits years 2001 to present. FASS Fuel Air System or "FASS Ride". This replacement canister is design with the purpose of saving money. Must have a fass fuel pump to be able to use this delete accessory. It can be easily be removed, just follow the instructions giving to by fass, this product can only be use with Fass fuel pumps.
           
             
Delete OEM Filter
Eliminate Time and Costs 
Screws on in place of the stock filter
Allows fuel to flow unrestricted
Offers a gauge ports to monitor fuel pressure
Part Number: DFD-4000
Price for this products is $84.55 USA Dollars 
Fits Duramax years 2001 to present
Instructions are included for installation 

FASS Fuel Systems
After the installation of an aftermarket filtration system such as a Fass Fuel System 95 gph Platinum or 150 gph Titanium Series lift pump the factory fuel filter becomes unnecessary. This delete canister will allow for the removal of the factory fuel filter by replacing the filter with a hollow canister that provides a clean looking installation and maintains the OEM fuel filter sensor. By removing the factory fuel filter you will no longer have to pay the expensive costs of replacing the filter every 4,000 miles, saving you money and eliminating one more restriction in the fueling system. If you have questions regarding installation please give us a call at 866-488-6942 or visit our website www.toxicdiesel.com 
Duramax Fuel Filter Delete 
Note: This system must be used with another form of fuel filtration, such as Titanium 95 gph or higher pressure volume pumps. FASS Fuel Air Separation System.

FASS Fuel Systems FREE Shipping
Free Shipping 
FREE Shipping Lower 49 state and we have distribution in Canada Diesel Performance call before ordering parts to Canada to make sure we have them available.

 Toxic Diesel Source:


Popular posts from this blog

Duramax 6.6L Valve Lash Adjustment

Duramax 6.6L Valve Adjustment  Duramax Diesel Pickup Truck This is one method used to set the valve lash on your duramax engine Valve adjustment should be performed anytime the heads are removed. It's also good practice to adjust valves during service that require valve cover remove.  TDC (Top Dead Center) First start with, locating the timing mark on the front engine cover and the harmonic balance.  Rotate the crankshaft in order to bring the number 1 cylinder to TDC (Top Dead Center) of the exhaust stroke. This mark should be aligned with the mark on the engine.  To adjust the valves, start by loosening all the jam nuts with a 14mm wrench, you will also need a flat screwdriver to make the adjustments. Adjust the valve using a .012" feeler gauge Use your .012” feeler gauge between the rocker arm and the valve bridge as pictured. The correct setting is had when there is slight resistance when moving the feeler gauge. It should not...
Read more

Duramax Glow Plugs Operation Glow Plug Relay

                                                    Cold Weather Starts and Glow Plugs  Glow Plug System Description Duramax diesel engine, air alone is compressed in the cylinder. Then, after the air has been compressed, a charge of fuel is sprayed into the cylinder and ignition occurs, due to the heat of compression. Eight glow plugs are used as an aid to starting. The glow plug initial ON time will vary based on the system voltage and temperature. Lower temperatures cause longer ON times all the times. The ECM provides glow plug operation after starting a cold engine. This post-start operation is initiated when the ignition switch  is returned to Run, from the Start position. This operation helps clean up excessive white smoke or poor idle quality after starting. Control of the instant start system, glow plugs is determine...
Read more

Duramax Diesel Allison Transmission Fast Learn Procedure

Duramax Equipped With a Allison Transmission Fast Learn Procedure   Initial Test Automatic 5 or 6 Speed Transmission  In general, Fast Learn is a procedure for Allison 1000 Series transmissions in which a series of tests are run to allow the transmission control module TCM to learn individual Clutch characteristics. Once the clutch data is learned, Fast Learn translates it to the adaptive data cells, which the TCM uses for clutch control during range shifts. Fast Learn is used at GM plants, and allows the vehicle to be driven out of the assembly plant in a near fully adapted state to minimize any customer shift concerns. The scan tool version of Fast Learn is intended to provide the same benefit following transmission repair or replacement at your local shop or Diesel Transmissions Performance Specialist .                                    BD Diesel Power Or...
Read more