Skip to main content

Duramax Dual Cp3 Fuel Injection Pumps



Duramax Diesel Dual Cp3 Fuel Injection Pumps 

Feed the demand of your injectors by being able to supply more fuel
The CP3 Injection pump is found on Cummins and Duramax Common Rail diesels, and is the fuel pump that pressurizes the fuel, over 25,000 PSI. Under the high demand of fuel in some high horsepower tunes, stock pump simply cannot keep up with the commanded volume or pressure. When this happens, you get a condition refered to as "draining the rail". What this means is that your injectors have let out more fuel that the CP3 pump can produce at a given time. Here are some of the most popular Cp3 Fuel Pump Companies that offer these products.






ATS Duramax Twin Cp3 Fuel Injection Kit 
ATS Twin Fueler System for the 2004.5-2010 Duramax doubles the fueling capability when running large tunes and bigger injectors. The system is not only designed to work in conjunction with the factory CP3, but it also maximizes the system. Utilizing ported rail fitting, larger diameter high pressure fuel lines, and a true twin system, the ATS kit allows for huge amounts of power and reliability. 
ATS Diesel CP3 with Fuel Pump PN/7019004290 Price $2232.50 Free Shipping 




Pacific Performance Engineering Duramax Dual Fueler Cp3 Kit 
Two is better than one, and the PPE Dual Fueler Kit proves it. On a modified engine, the stock CP3 pump runs out of fuel well before the engine stops producing power. The solution is a second belt-driven Bosch CP3 fuel pump that works in conjunction with the stock fuel system and is controlled by a sophisticated microprocessor module.
The PPE Dual Fueler Kit produces twice as much pumping capacity and increases fuel volume. Adding a PPE Dual Fueler Kit to your stock fuel system reduces drive load on the internal gear driven CP3 pump, thereby increasing pump reliability. Both pumps work together, each delivering half the total volume of fuel required
PPE Diesel Dual Fueler CP3 Fuel Duramax Pumps PN/113063000 Price $2115.00 Free Shipping 




Industrial Injection Duramax Diesel Dual Twin Cp3 Fuel Systems 
The New Industrial Injection Dual CP3 is the ultimate in performance. Efficiency is increased and EGT's reduced while providing enough fuel to make over 1200HP.
Both pumps work together by delivering half the total volume of fuel required. Since each pump now shares the total fuel delivery, drive load on the original internal cp3 pump is reduced by 50%. This not only increases reliability but also reduces wear and tear. The dual CP3 kit provides a seamless and consistent fuel flow for large injectiors and aggressive programming that demands a high volume of fuel and optimal fuel rail pressure. As an added benefit, in the event of pump failure Industrial Injection's controller will automatically switch full fuel delivery control to the remaining functioning pump.
industrial Injection Duramax Twin Fuel Cp3 Pumps PN/DCP3CLLY Price $2275.00 Free Shipping 





HS Motorsports Duel High Pressure 
The CP3 pump we include with the kit is a brand new OEM unit from Bosch. That's right, BRAND NEW, not a remanufactured unit like many shops include. The key to ensuring the longevity of any high pressure fuel pump is by providing the high pressure fuel system with clean, waterless diesel fuel. Any fuel contamination that reaches the high pressure fuel system can be detrimental to reliability and performance. We highly recommend using AirDog or Fass Ride lift pump for proper filtration and water-separation.
HS Motorsports High Pressure Dual Cp3 Duramax Pump PN/131001 Price $2799.00 Free Shipping 


Available at Toxic Diesel Performance, we hope this will help you out on making the best choice purchase for your next project.


866-488-6942

Popular posts from this blog

Duramax 6.6L Valve Lash Adjustment

Duramax 6.6L Valve Adjustment  Duramax Diesel Pickup Truck This is one method used to set the valve lash on your duramax engine Valve adjustment should be performed anytime the heads are removed. It's also good practice to adjust valves during service that require valve cover remove.  TDC (Top Dead Center) First start with, locating the timing mark on the front engine cover and the harmonic balance.  Rotate the crankshaft in order to bring the number 1 cylinder to TDC (Top Dead Center) of the exhaust stroke. This mark should be aligned with the mark on the engine.  To adjust the valves, start by loosening all the jam nuts with a 14mm wrench, you will also need a flat screwdriver to make the adjustments. Adjust the valve using a .012" feeler gauge Use your .012” feeler gauge between the rocker arm and the valve bridge as pictured. The correct setting is had when there is slight resistance when moving the feeler gauge. It should not be so tight th

How to Remove LB7 Duramax Fuel Injectors Step By Step Instructions

LB7 Duramax Diesel 6.6L R&R Remove and Replace  Working on any automobile engine can be intimidating, and that is the very reason why mechanics stay in business, However some tasks that seem intimidating are not actually that difficult if you have the right tools and the right knowledge to complete the task at hand, The following instructions are on how to remove LB7 Duramax Fuel Injectors. This task is often considered a difficult process to complete, but these instructions will break down the process and make this task seem simple. Duramax Diesel LB7 Engine 2001-2004 GMC or Chevrolet Pick-up Truck  Drain the Coolant find the drain valve on the passenger side of the wheel well and drain the coolant. To capture the debris,use a bucket and a cloth for a filter. Caution: This step is very important to ensure the combustion chamber won't fill with coolant during the last step of removing the  fuel injectors if an injector cup pull out during this step.

Duramax Glow Plugs Operation Glow Plug Relay

                                                    Cold Weather Starts and Glow Plugs  Glow Plug System Description Duramax diesel engine, air alone is compressed in the cylinder. Then, after the air has been compressed, a charge of fuel is sprayed into the cylinder and ignition occurs, due to the heat of compression. Eight glow plugs are used as an aid to starting. The glow plug initial ON time will vary based on the system voltage and temperature. Lower temperatures cause longer ON times all the times. The ECM provides glow plug operation after starting a cold engine. This post-start operation is initiated when the ignition switch  is returned to Run, from the Start position. This operation helps clean up excessive white smoke or poor idle quality after starting. Control of the instant start system, glow plugs is determine by an electronic glow plug control unit and  4.7 volt  glow plugs, requiring  2 seconds  to heat up to  1,000°C (1,832°F)  . The temperature and t