Skip to main content

Diablosport i2 inTune Duramax Programmer

InTuner i2 Performance Programmer for GM Vehicles


 Get The Best Performance Upgrade For Your Ride
Upgrade your horsepower in minutes with our inTune i2 Power Programmer. It is easy to install and plugs right into your vehicle's OBD-II port. Our tuning team maps out all the i2'stunes for your exact car or diesel truck. Our goal is to make the biggest power gain, with the largest choice of performance options. The i2 features the latest electronics in diesel performance; find our more about what makes the i2 the best diesel handheld tuner in the market available.

Why Tune Just One Truck 
The New inTune i2 allows for a first time to tune multiple trucks using The i2 DiabloSport tuner. All you have to do is purchase a tuning license, If you have a 2016 Chevrolet Camaro or a 2016 GMC Sierra, you can get a license that let you to tune both at the same time! 

The Most Powerful tuner For GM Diesel Truck 
The new i2 tuner can make your truck feel brand new all over again! is has tuning options for power or mileage, and a new "Easy Tuner" mode that walks you through the whole tuning process. The tunes will adjust your truck throttle response, enhance towing performance, and increase your fuel economy without even getting your hands dirty!. The i2 programmer will become your truck's perfect companion. The i2 programmer for diesel's options will let you go from mile to extreme. There is a setting for Towing, Fuel Economy, and High Performance "Race" all tailored to what you need our of your tuner using the i2. Whether you just want to put a quick tune on your truck, change your tires size or custom tune for more power, the inTune i2 is the perfect performance upgrade for your GMC/Chevrolet Diesel Truck. 

inTune i2 Programmer key Duramax Diesel Tuning Features:

1. Add up to 100 Horse Power and 200 Ft of Torque
2. Boost Towing Performance
3. Increase Fuel Economy
4. Check and Clear Engine Lights DTC's
5. Custom Programmer Multiple Truck with One Unit 
6. Truck Years 2001-2010
7. P/N: i2010-Cummins, i2020-Powerstroke, i2030-Duramax


866-488-6942

Location: Utah, USA

Popular posts from this blog

Duramax 6.6L Valve Lash Adjustment

Duramax 6.6L Valve Adjustment  Duramax Diesel Pickup Truck This is one method used to set the valve lash on your duramax engine Valve adjustment should be performed anytime the heads are removed. It's also good practice to adjust valves during service that require valve cover remove.  TDC (Top Dead Center) First start with, locating the timing mark on the front engine cover and the harmonic balance.  Rotate the crankshaft in order to bring the number 1 cylinder to TDC (Top Dead Center) of the exhaust stroke. This mark should be aligned with the mark on the engine.  To adjust the valves, start by loosening all the jam nuts with a 14mm wrench, you will also need a flat screwdriver to make the adjustments. Adjust the valve using a .012" feeler gauge Use your .012” feeler gauge between the rocker arm and the valve bridge as pictured. The correct setting is had when there is slight resistance when moving the feeler gauge. It should not...
Read more

Duramax Glow Plugs Operation Glow Plug Relay

                                                    Cold Weather Starts and Glow Plugs  Glow Plug System Description Duramax diesel engine, air alone is compressed in the cylinder. Then, after the air has been compressed, a charge of fuel is sprayed into the cylinder and ignition occurs, due to the heat of compression. Eight glow plugs are used as an aid to starting. The glow plug initial ON time will vary based on the system voltage and temperature. Lower temperatures cause longer ON times all the times. The ECM provides glow plug operation after starting a cold engine. This post-start operation is initiated when the ignition switch  is returned to Run, from the Start position. This operation helps clean up excessive white smoke or poor idle quality after starting. Control of the instant start system, glow plugs is determine...
Read more

Duramax Diesel Allison Transmission Fast Learn Procedure

Duramax Equipped With a Allison Transmission Fast Learn Procedure   Initial Test Automatic 5 or 6 Speed Transmission  In general, Fast Learn is a procedure for Allison 1000 Series transmissions in which a series of tests are run to allow the transmission control module TCM to learn individual Clutch characteristics. Once the clutch data is learned, Fast Learn translates it to the adaptive data cells, which the TCM uses for clutch control during range shifts. Fast Learn is used at GM plants, and allows the vehicle to be driven out of the assembly plant in a near fully adapted state to minimize any customer shift concerns. The scan tool version of Fast Learn is intended to provide the same benefit following transmission repair or replacement at your local shop or Diesel Transmissions Performance Specialist .                                    BD Diesel Power Or...
Read more