Skip to main content

Duramax Allison Transmission 3 Disc Torque Converter

                   BD Diesel Duramax Allison Transmission Component and System Description 

Engine/Transmission Connection 
The converter housing of 1000 Series transmissions mates directly to the engine block. DB Diesel Flex plate drive is used for engine to transmission torque transfer.

 DB Diesel Duramax Torque Converter  
Several torque converter are available to match the transmissions to a wide variety of diesel and engines. The torque converter is a single-stage, poly phase, and 3-element unit, consisting of a pump, stator, and turbine. At lower output speeds, the torque converter multiplies torque and provides a fluid coupling to the engine. At higher speeds, the torque converter clutch. is automatically engaged to provide direct drive from the engine to the transmission. Hydraulic fluid for converter charging pressure comes from the sump and is supplied by the input pump. The TCC is applied or released by changing direction of fluid in the torque converter. An integral converter damper minimizes the need for additional engine vibration control.


BD Diesel Stage 5 Clutch Kit 
5 clutches, 2 rotating and 3 stationary, direct the flow of torque through the transmission. All range clutches are hydraulically actuated and spring-released, with automatic wear compensation. The transmission fluid cools the clutches. The transmission control module TCM signals solenoid valves to apply and release clutches based on speed and power combinations and the range selected by the operator.

Transmission Fluid Filtration 
Fluid filtration is provided by 2 filter systems. A suction filter, located in the sump, provides general protection to the entire hydraulic system by filtering large particulates. A spin-on filter provides full-time protection for the control solenoids and multiply pass protection for the entire system. The spin-on filter is externally located on the converter housing at the lower left front of the transmission.

  Control Valve Assembly 
The control valve assembly consists of 2 components. The main DB Diesel valve body contains the pressure control valves, the TCC valve, the exhaust back fill valve, and the control main relief valve. The shift valve bodie contains the shift valves, the control main pressure valve, and the manual selector valve. The control valve assembly attaches to the bottom of the main case module and is enclosed by the oil pan.

BD Diesel Remote Oil Cooler Provision 
Ports for remote-mount oil cooler lines are located on the right side of the converter housing near the converter housing/main housing spline. Remote oil-to-water coolers require plumbing for transmission fluid and engine-cooling water. Remote oil-to-air coolers may also be used and only transmission fluid lines need to be provided. Heat is transferred from the transmission fluid to either water or air depending upon the cooler type used..

                                             http://www.toxicdiesel.com/ 866-488-6942

Popular posts from this blog

Duramax 6.6L Valve Lash Adjustment

Duramax 6.6L Valve Adjustment  Duramax Diesel Pickup Truck This is one method used to set the valve lash on your duramax engine Valve adjustment should be performed anytime the heads are removed. It's also good practice to adjust valves during service that require valve cover remove.  TDC (Top Dead Center) First start with, locating the timing mark on the front engine cover and the harmonic balance.  Rotate the crankshaft in order to bring the number 1 cylinder to TDC (Top Dead Center) of the exhaust stroke. This mark should be aligned with the mark on the engine.  To adjust the valves, start by loosening all the jam nuts with a 14mm wrench, you will also need a flat screwdriver to make the adjustments. Adjust the valve using a .012" feeler gauge Use your .012” feeler gauge between the rocker arm and the valve bridge as pictured. The correct setting is had when there is slight resistance when moving the feeler gauge. It should not be so tight th
Read more

Duramax Glow Plugs Operation Glow Plug Relay

                                                    Cold Weather Starts and Glow Plugs  Glow Plug System Description Duramax diesel engine, air alone is compressed in the cylinder. Then, after the air has been compressed, a charge of fuel is sprayed into the cylinder and ignition occurs, due to the heat of compression. Eight glow plugs are used as an aid to starting. The glow plug initial ON time will vary based on the system voltage and temperature. Lower temperatures cause longer ON times all the times. The ECM provides glow plug operation after starting a cold engine. This post-start operation is initiated when the ignition switch  is returned to Run, from the Start position. This operation helps clean up excessive white smoke or poor idle quality after starting. Control of the instant start system, glow plugs is determine by an electronic glow plug control unit and  4.7 volt  glow plugs, requiring  2 seconds  to heat up to  1,000°C (1,832°F)  . The temperature and t
Read more

How to Remove LB7 Duramax Fuel Injectors Step By Step Instructions

LB7 Duramax Diesel 6.6L R&R Remove and Replace  Working on any automobile engine can be intimidating, and that is the very reason why mechanics stay in business, However some tasks that seem intimidating are not actually that difficult if you have the right tools and the right knowledge to complete the task at hand, The following instructions are on how to remove LB7 Duramax Fuel Injectors. This task is often considered a difficult process to complete, but these instructions will break down the process and make this task seem simple. Duramax Diesel LB7 Engine 2001-2004 GMC or Chevrolet Pick-up Truck  Drain the Coolant find the drain valve on the passenger side of the wheel well and drain the coolant. To capture the debris,use a bucket and a cloth for a filter. Caution: This step is very important to ensure the combustion chamber won't fill with coolant during the last step of removing the  fuel injectors if an injector cup pull out during this step.
Read more