Skip to main content

LMM Duramax Intercoolers By PPE Diesel

         Pacific Performance Engineering is the product you have bean looking for you truck duramax diesel.

It has been shown that the factory GM intercooler causes a 2 to 3 psi pressure drop, so the boost from even the largest turbocharger can be choked if the intercooler is inefficient and making less power.

PPE’s High Flow Performance Intercooler, pressure drop wasted energy is virtually eliminated. There is simply no comparison between the effectiveness of the PPE High Flow Performance Intercooler and the stock unit. 

 Providing 2,142 cu. in. of cooling volume, which is 98% more volume over the stock unit’s 1,083 cu. in., the PPE’s High-Flow Performance Intercooler not only cools a larger volume of air but it also does it faster and more efficiently. 

In fact, PPE’s intercooler is the largest and most efficient intercooler in the industry. All of which equals more horsepower and fuel economy for your truck, and it still fits into the stock mounting holes! Optional studded end tanks are available for high-boost applications of 55 to 100 PSI.
The PPE Diesel Intercooler Features:
1. Exact fit int the stock mounting holes 
2. All-Aluminum Construction
3. Design to reduced EGT numbers (Exhaust Gas Temperature).
4. Increase efficiency, reduce pressure drop across intercooler.
5. Increase fuel economy.

Popular posts from this blog

Duramax 6.6L Valve Lash Adjustment

Duramax 6.6L Valve Adjustment  Duramax Diesel Pickup Truck This is one method used to set the valve lash on your duramax engine Valve adjustment should be performed anytime the heads are removed. It's also good practice to adjust valves during service that require valve cover remove.  TDC (Top Dead Center) First start with, locating the timing mark on the front engine cover and the harmonic balance.  Rotate the crankshaft in order to bring the number 1 cylinder to TDC (Top Dead Center) of the exhaust stroke. This mark should be aligned with the mark on the engine.  To adjust the valves, start by loosening all the jam nuts with a 14mm wrench, you will also need a flat screwdriver to make the adjustments. Adjust the valve using a .012" feeler gauge Use your .012” feeler gauge between the rocker arm and the valve bridge as pictured. The correct setting is had when there is slight resistance when moving the feeler gauge. It should not be so tight th
Read more

Duramax Glow Plugs Operation Glow Plug Relay

                                                    Cold Weather Starts and Glow Plugs  Glow Plug System Description Duramax diesel engine, air alone is compressed in the cylinder. Then, after the air has been compressed, a charge of fuel is sprayed into the cylinder and ignition occurs, due to the heat of compression. Eight glow plugs are used as an aid to starting. The glow plug initial ON time will vary based on the system voltage and temperature. Lower temperatures cause longer ON times all the times. The ECM provides glow plug operation after starting a cold engine. This post-start operation is initiated when the ignition switch  is returned to Run, from the Start position. This operation helps clean up excessive white smoke or poor idle quality after starting. Control of the instant start system, glow plugs is determine by an electronic glow plug control unit and  4.7 volt  glow plugs, requiring  2 seconds  to heat up to  1,000°C (1,832°F)  . The temperature and t
Read more

How to Remove LB7 Duramax Fuel Injectors Step By Step Instructions

LB7 Duramax Diesel 6.6L R&R Remove and Replace  Working on any automobile engine can be intimidating, and that is the very reason why mechanics stay in business, However some tasks that seem intimidating are not actually that difficult if you have the right tools and the right knowledge to complete the task at hand, The following instructions are on how to remove LB7 Duramax Fuel Injectors. This task is often considered a difficult process to complete, but these instructions will break down the process and make this task seem simple. Duramax Diesel LB7 Engine 2001-2004 GMC or Chevrolet Pick-up Truck  Drain the Coolant find the drain valve on the passenger side of the wheel well and drain the coolant. To capture the debris,use a bucket and a cloth for a filter. Caution: This step is very important to ensure the combustion chamber won't fill with coolant during the last step of removing the  fuel injectors if an injector cup pull out during this step.
Read more