Edge Jammer Cold Air Intake System

Edge Products Cold Air Intake

Edge Jammer CAI

2016 is set to start with a bang as Edge has unveiled brand new cold air intake kits for diesel trucks; The Jammer CAI. The Jammer kits are designed with the same level of quality and innovation as the complete line of Edge tuning products. Numerous months and man hours have been put in to pair the all-new Jammer kits with the Edge Evolution, Juice with Attitude, and EvoHT tuning devices for quality assurance and impressive performance.

Edge Products

The Jammer CAI's revolutionary design improves airflow by blocking hot air and using cooler, denser air for optimal efficiency. Edge's performance tuning, combined with the Jammer CAI, offers best-in-class results for maximum performance, and improved continuous power. The Jammer CAI uses a large diameter intake tube that is smoother, has less bends and wider providing uninterrupted airflow. By itself, you'll notice an increase in power and especially when the throttle is wide open. Team up the Jammer CAI with other Edge performance products and you'll create a much more efficient system with maximum gains in power, mileage, and efficiency.

Edge Products Duramax Jammer CAI

Edge's Rep Jared Venz says. "By itself, the Edge Jammer CAI will increase power, especially when you pair up The EDGE Jammer and a EDGE Tuner, you'll create a much more efficient system with maximum gains in power, mileage, and efficiency." The models currently cover late model Ford, GM and Doge pickups. For more information, visit Toxic Diesel Performance.

JAMMER CAI 2011-2016 FORD 6.7L 18215

JAMMER CAI 2011-2014 CHEVY 6.6L 28230

JAMMER CAI 2015 CHEVY 6.6L 28248

JAMMER CAI 2007-2009 DODGE 6.7L 38175

JAMMER CAI 2010-2012 DODGE 6.7L 38180

Key Features

• High Density, Cold Air Intake • Increased Horsepower & Fuel Economy • Compatible with Edge Tuning Products • Enclosed Housing for Superior Cool Airflow • Improves Continuous Power • Lifetime Reusable Filter • High Flow, Low Restriction • Pre-Oiled Filter

Toxic Diesel Performance

Edge Products

866-488-6942

Duramax 6.6L Valve Lash Adjustment

Duramax 6.6L Valve Adjustment Duramax Diesel Pickup Truck This is one method used to set the valve lash on your duramax engine Valve adjustment should be performed anytime the heads are removed. It's also good practice to adjust valves during service that require valve cover remove. TDC (Top Dead Center) First start with, locating the timing mark on the front engine cover and the harmonic balance. Rotate the crankshaft in order to bring the number 1 cylinder to TDC (Top Dead Center) of the exhaust stroke. This mark should be aligned with the mark on the engine. To adjust the valves, start by loosening all the jam nuts with a 14mm wrench, you will also need a flat screwdriver to make the adjustments. Adjust the valve using a .012" feeler gauge Use your .012” feeler gauge between the rocker arm and the valve bridge as pictured. The correct setting is had when there is slight resistance when moving the feeler gauge. It should not be so tight th

Duramax Glow Plugs Operation Glow Plug Relay

Cold Weather Starts and Glow Plugs Glow Plug System Description Duramax diesel engine, air alone is compressed in the cylinder. Then, after the air has been compressed, a charge of fuel is sprayed into the cylinder and ignition occurs, due to the heat of compression. Eight glow plugs are used as an aid to starting. The glow plug initial ON time will vary based on the system voltage and temperature. Lower temperatures cause longer ON times all the times. The ECM provides glow plug operation after starting a cold engine. This post-start operation is initiated when the ignition switch is returned to Run, from the Start position. This operation helps clean up excessive white smoke or poor idle quality after starting. Control of the instant start system, glow plugs is determine by an electronic glow plug control unit and 4.7 volt glow plugs, requiring 2 seconds to heat up to 1,000°C (1,832°F) . The temperature and t

How to Remove LB7 Duramax Fuel Injectors Step By Step Instructions

LB7 Duramax Diesel 6.6L R&R Remove and Replace Working on any automobile engine can be intimidating, and that is the very reason why mechanics stay in business, However some tasks that seem intimidating are not actually that difficult if you have the right tools and the right knowledge to complete the task at hand, The following instructions are on how to remove LB7 Duramax Fuel Injectors. This task is often considered a difficult process to complete, but these instructions will break down the process and make this task seem simple. Duramax Diesel LB7 Engine 2001-2004 GMC or Chevrolet Pick-up Truck Drain the Coolant find the drain valve on the passenger side of the wheel well and drain the coolant. To capture the debris,use a bucket and a cloth for a filter. Caution: This step is very important to ensure the combustion chamber won't fill with coolant during the last step of removing the fuel injectors if an injector cup pull out during this step.

Toxic Performance

Search This Blog