Skip to main content

EZ Lynk Duramax 6.6L Diesel Tuning

GDP Tuning Diesel Performance 
The AutoAgent connects to the vehicles via the OBDII-port and broadcasts a Wi-Fi access point (AP) which allows a wireless connection to the vehicle using any iOS device (Android support coming soon – will also support the inexpensive Android monitors). By launching the free EZ LYNK application on an iOS device, engine data is seamlessly streamed to the phone or other smart devices. The AutoAgent also has the capability to reflash vehicle system controllers with ECU profiles shared by technicians.
EZ Lynk
Technicians will quickly learn to appreciate the EZ LYNK Cloud where they can easily manage customers/vehicles and all the data associated with them (datalogs, engine profiles, vehicles information). Transferring engine profiles via USB connection, SD card or e-mail are now a thing of the past as technicians have the capability to share engine profiles with the click of a button to completely eliminate user-error from the equation.
On the other side of things, the end-user can conveniently share datalogs and other vehicle information to any technician with the touch of a finger without even leaving the driver seat. Datalogs can be quickly started and stopped from the main gauge display screen and bookmarks can be added to draw interest to the specific points of a datalog if desired. A graphical web-based datalog viewing solution will soon be incorporated into the EZ LYNK Cloud as well.
A fully customizable user interface allows the end-user to create a gauge interface that suits their particular needs. Technicians can also create default PID configurations that are automatically loaded during a reflash procedure to further assist in the troubleshooting and diagnostic process.

EZ Lynk requires use of a Apple or Android device to function, Must have iOS 8.0 or higher, iPad, iPod touch, iPhone

Popular posts from this blog

Duramax 6.6L Valve Lash Adjustment

Duramax 6.6L Valve Adjustment  Duramax Diesel Pickup Truck This is one method used to set the valve lash on your duramax engine Valve adjustment should be performed anytime the heads are removed. It's also good practice to adjust valves during service that require valve cover remove.  TDC (Top Dead Center) First start with, locating the timing mark on the front engine cover and the harmonic balance.  Rotate the crankshaft in order to bring the number 1 cylinder to TDC (Top Dead Center) of the exhaust stroke. This mark should be aligned with the mark on the engine.  To adjust the valves, start by loosening all the jam nuts with a 14mm wrench, you will also need a flat screwdriver to make the adjustments. Adjust the valve using a .012" feeler gauge Use your .012” feeler gauge between the rocker arm and the valve bridge as pictured. The correct setting is had when there is slight resistance when moving the feeler gauge. It should not be so tight th
Read more

Duramax Glow Plugs Operation Glow Plug Relay

                                                    Cold Weather Starts and Glow Plugs  Glow Plug System Description Duramax diesel engine, air alone is compressed in the cylinder. Then, after the air has been compressed, a charge of fuel is sprayed into the cylinder and ignition occurs, due to the heat of compression. Eight glow plugs are used as an aid to starting. The glow plug initial ON time will vary based on the system voltage and temperature. Lower temperatures cause longer ON times all the times. The ECM provides glow plug operation after starting a cold engine. This post-start operation is initiated when the ignition switch  is returned to Run, from the Start position. This operation helps clean up excessive white smoke or poor idle quality after starting. Control of the instant start system, glow plugs is determine by an electronic glow plug control unit and  4.7 volt  glow plugs, requiring  2 seconds  to heat up to  1,000°C (1,832°F)  . The temperature and t
Read more

How to Remove LB7 Duramax Fuel Injectors Step By Step Instructions

LB7 Duramax Diesel 6.6L R&R Remove and Replace  Working on any automobile engine can be intimidating, and that is the very reason why mechanics stay in business, However some tasks that seem intimidating are not actually that difficult if you have the right tools and the right knowledge to complete the task at hand, The following instructions are on how to remove LB7 Duramax Fuel Injectors. This task is often considered a difficult process to complete, but these instructions will break down the process and make this task seem simple. Duramax Diesel LB7 Engine 2001-2004 GMC or Chevrolet Pick-up Truck  Drain the Coolant find the drain valve on the passenger side of the wheel well and drain the coolant. To capture the debris,use a bucket and a cloth for a filter. Caution: This step is very important to ensure the combustion chamber won't fill with coolant during the last step of removing the  fuel injectors if an injector cup pull out during this step.
Read more